Home Order Catalog Online Catalog New Items Contact Us
 Prev 
i
WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**
117
'65-69 CAR SHIFTER
1965-69 SHIFTER PARTS – 3 & 4 SPEED: All Parts Fit All Years Exc, As Noted.
QUICK SHIFTER KITS – see page 118
Bronze Shifter Bushing Kit: 1965-69 – In use since 1974
These bronze bushings replace the original plastic bushings at the front and back of the shift tube. The
plastic ones quite easily pop out, allowing a great deal of play. By installing these bronze bushings, you will
have easier, more positive shifting. Another added benefit is that the shifter will be much less apt to rattle
on rough roads. Installation time is about 1-2 hours. Directions are easy. Fits new or used shifters. This is the
time to check other shifter parts.
C1 SET: For new or used rods. Includes: (2) machined bronze bushings, hardware, detailed instructions.
C1 SET 4 oz./set
C1BB BUSHINGS ONLY: You may purchase just the machined bronze bushings for the shift rod. You then
can braze or solder them in place.
C1BB = 2 BUSHINGS ONLY 4 oz.
PICTURE # Be sure to consider all the following parts for complete shifter job.
1. Shifter Plastic Base: Fits between shifter base and floor (see page 118). These are being machined from DELRIN (a self lubricating high quality "nylon") and appear just
like the originals but are vastly superior to the original "plastic". C537D 4 oz.
2. Lower Seal: See page 118 – "SHIF T LEVER SEALS & SHIMS"
3. Shifter Tube: Old ones get rusty, stabilizer rod mount often breaks off. Well wor th replacing if shifter binds or is sloppy. C128 7 lbs.
4. Shifter Shaft (Rod): Goes from shift lever to transmission coupler. Apt to rust and bind. C129 4 lbs.
5. Bolt Kit: F or coupler. C2146 2 oz.
8. Clamp: Coupler into rod. Usually badly rusted. C181A 4 oz.
10 & 11. Special Small Washer & Cotter Pin: On shifter pin. C2200 1 oz.
12.
Shift Rod Coupler: Original Rubber – Attaches to shif t rod and (by pin C43) attaches to transmission. Shaft pin hole wears and/or internal rubber
mount loosens causing sloppy shifting and no reverse. C131R 1 lb.
Coupler with NYLON: Made just like our stock couplers but with a nylon insert. This gives very positive shifts but may allow some shifter vibration.
1961-69 CARS & FC C131RN 1 lb.
13.
Pin: Shift coupler to transmission – Wears and causes sloppy shifting C43 1 oz.
14. Bolt Kit: 2 bolts, flat & lock washers C4437 4 oz./set
15. Set of 2 Nuts C4438 2 oz./set
18. Retainer: Threaded holes – control rod bracket; 65-69 standards CX6346 4 oz.
20. Stabilizing Rod: For shifter tube. Often rusty and broken. 1965 Repro – STEEL C132R 8 oz.
1966-69 Repro – STEEL C132AR 8 oz.
21. Dished Washers: Holds rubber bushings on rod; 2 needed. C395L 2 oz.
Non-original $ Saver Washers (2 needed) C395X 2 oz.
22. Rubber Bushings for Stabilizer Rod: 2 needed. C396L 2 oz.
SEAL – Trans. Selector Shaft – '64-69 C497 2 oz.
Improved Seal: See page 115 (#17) for more info.
MULTI-KITS
see Blue pg. MK-13
Shift Boot
See Page 115
C2200
C181A
C43
C131R
C497
see page 235
iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**117'65-69 CAR SHIFTER1965-69 SHIFTER PARTS - 3 & 4 SPEED: All Parts Fit All Years Exc, As Noted.QUICK SHIFTER KITS - see page 118Bronze Shifter Bushing Kit: 1965-69 - In use since 1974These bronze bushings replace the original plastic bushings at the front and back of the shift tube. The plastic ones quite easily pop out, allowing a great deal of play. By installing these bronze bushings, you will have easier, more positive shifting. Another added benefit is that the shifter will be much less apt to rattle on rough roads. Installation time is about 1-2 hours. Directions are easy. Fits new or used shifters. This is the time to check other shifter parts.C1 SET: For new or used rods. Includes: (2) machined bronze bushings, hardware, detailed instructions. C1 SET 4 oz./setC1BB BUSHINGS ONLY: You may purchase just the machined bronze bushings for the shift rod. You then can braze or solder them in place. C1BB = 2 BUSHINGS ONLY 4 oz.PICTURE # Be sure to consider all the following parts for complete shifter job.1. Shifter Plastic Base: Fits between shifter base and floor (see page 118). These are being machined from DELRIN (a self lubricating high quality "nylon") and appear just like the originals but are vastly superior to the original "plastic". C537D 4 oz.2. Lower Seal: See page 118 - "SHIF T LEVER SEALS & SHIMS"3. Shifter Tube: Old ones get rusty, stabilizer rod mount often breaks off. Well wor th replacing if shifter binds or is sloppy. C128 7 lbs.4. Shifter Shaft (Rod): Goes from shift lever to transmission coupler. Apt to rust and bind. C129 4 lbs.5. Bolt Kit: F or coupler. C2146 2 oz. 8. Clamp: Coupler into rod. Usually badly rusted. C181A 4 oz. 10 & 11. Special Small Washer & Cotter Pin: On shifter pin. C2200 1 oz. 12. Shift Rod Coupler: Original Rubber - Attaches to shif t rod and (by pin C43) attaches to transmission. Shaft pin hole wears and/or internal rubber mount loosens causing sloppy shifting and no reverse. C131R 1 lb. Coupler with NYLON: Made just like our stock couplers but with a nylon insert. This gives very positive shifts but may allow some shifter vibration. 1961-69 CARS & FC C131RN 1 lb. 13. Pin: Shift coupler to transmission - Wears and causes sloppy shifting C43 1 oz. 14. Bolt Kit: 2 bolts, flat & lock washers C4437 4 oz./set15. Set of 2 Nuts C4438 2 oz./set 18. Retainer: Threaded holes - control rod bracket; 65-69 standards CX6346 4 oz.20. Stabilizing Rod: For shifter tube. Often rusty and broken. 1965 Repro - STEEL C132R 8 oz. 1966-69 Repro - STEEL C132AR 8 oz.21. Dished Washers: Holds rubber bushings on rod; 2 needed. C395L 2 oz. Non-original $ Saver Washers (2 needed) C395X 2 oz.22. Rubber Bushings for Stabilizer Rod: 2 needed. C396L 2 oz.SEAL - Trans. Selector Shaft - '64-69 C497 2 oz. Improved Seal: See page 115 (#17) for more info.MULTI-KITSsee Blue pg. MK-13Shift BootSee Page 115C2200C181AC43C131RC497see page 235
Next
CLARKS- MORE THAN PARTS.

Copyright © 1978, 2019 Clark's Corvair Parts, Inc., "Clark's Corvair Parts" and the "Corvair Map" are registered service marks of Clark's Corvair Parts, Inc.
P.O.Box #NET 400 Mohawk Trail Shelburne Falls, MA 01370 USA All rights reserved.
Main Office Phone: 413.625.9776 Fax: 413.625.8498