Home Order Catalog Online Catalog New Items Contact Us
 Prev 
i
WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**
Please Wear Gloves
Handling Panels
! VERY SHARP !
193
'65-69 CAR BODY PANELS
GAS FILLER POCKET – STEEL 1965-69 Reproduction
Goes inside left front fender.
C4272 2 lbs.
SEAL – GAS TANK FILLER
1961-69 Large round rubber seal that goes around neck and seals to body.
C536R 6 oz.
TOP FENDER PATCH PANELS
1965-69 FIBERGLASS Top of fender where it joins the windshield pillar and usually rusts.
Right side is where antenna usually is. Left side is corresponding area
on drivers side.
Panel is about 10" x 6" Left Side C6709 2 lbs.
Right Side C2554 2 lbs.
Not suggested for Convertibles.
1965-69 New Lower Steel
Windshield Panel
Note: This is a difficult panel to replace. The windshield must be removed and these stop about 2" from the left
and right end of the windshield because that area was originally part of the fenders.
STEEL REPRODUCTION
This is all new tooling with exact detail and all die cut edges. 1965-69 exact replacement
of the original.
STEEL C641XR 5 lbs.
SUGGESTED CLIPS – For trim on fiberglass panel C640X – page 209
WINDSHIELD REMOVAL & INSTALLATION SUPPLIES – See pages 207-209
WINDSHIELD PILLARS – OUTER
1965-69 FIBERGLASS Join from bottom windshield panel and extends approximately 20"
up windshield pillar where they usually rust. Extends from under stainless
windshield trim to side of pillar and about 2" into top of front fender.
Left C3734 2 lbs.
Right C3733 2 lbs.
STEEL ROCKER PANELS
ALL '65-69
EXACT PROFILE Steel Rocker Panels
These are NOT "SLIP" on. Your old one must be cut out for a correct weld in replacement. Come in 40" lengths.
Get 2 to do a full side. Goes from the seam hanging down at the bottom and weld under the door sill. COUPE and
4-DOOR were originally 16 GA, but the CONVERTIBLE are stronger 12 gauge & work fine for all models.
COUPE, CONVERTIBLE & 4-DOOR – 12GA C3350CT 16 lbs. ea. (2 needed per side)
Support Body
During Installation
PANEL DISCOUNT
page 186
RUBBER ROCKER PANEL DRAIN FLAP
65-69 C856 2 oz.
C856
iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**Please Wear Gloves Handling Panels! VERY SHARP !193'65-69 CAR BODY PANELSGAS FILLER POCKET - STEEL 1965-69 Reproduction Goes inside left front fender. C4272 2 lbs. SEAL - GAS TANK FILLER 1961-69 Large round rubber seal that goes around neck and seals to body. C536R 6 oz.TOP FENDER PATCH PANELS 1965-69 FIBERGLASS Top of fender where it joins the windshield pillar and usually rusts. Right side is where antenna usually is. Left side is corresponding area on drivers side. Panel is about 10" x 6" Left Side C6709 2 lbs. Right Side C2554 2 lbs. Not suggested for Convertibles.1965-69 New Lower SteelWindshield PanelNote: This is a difficult panel to replace. The windshield must be removed and these stop about 2" from the left and right end of the windshield because that area was originally part of the fenders.STEEL REPRODUCTIONThis is all new tooling with exact detail and all die cut edges. 1965-69 exact replacement of the original. STEEL C641XR 5 lbs. SUGGESTED CLIPS - For trim on fiberglass panel C640X - page 209WINDSHIELD REMOVAL & INSTALLATION SUPPLIES - See pages 207-209WINDSHIELD PILLARS - OUTER 1965-69 FIBERGLASS Join from bottom windshield panel and extends approximately 20" up windshield pillar where they usually rust. Extends from under stainless windshield trim to side of pillar and about 2" into top of front fender. Left C3734 2 lbs. Right C3733 2 lbs.STEEL ROCKER PANELS ALL '65-69EXACT PROFILE Steel Rocker PanelsThese are NOT "SLIP" on. Your old one must be cut out for a correct weld in replacement. Come in 40" lengths. Get 2 to do a full side. Goes from the seam hanging down at the bottom and weld under the door sill. COUPE and 4-DOOR were originally 16 GA, but the CONVERTIBLE are stronger 12 gauge & work fine for all models. COUPE, CONVERTIBLE & 4-DOOR - 12GA C3350CT 16 lbs. ea. (2 needed per side)Support Body During InstallationPANEL DISCOUNTpage 186RUBBER ROCKER PANEL DRAIN FLAP 65-69 C856 2 oz.C856
Next
Search In Corvair Catalog Content
CLARKS- MORE THAN PARTS.

Copyright © 1978, 2019 Clark's Corvair Parts, Inc., "Clark's Corvair Parts" and the "Corvair Map" are registered service marks of Clark's Corvair Parts, Inc.
P.O.Box #NET 400 Mohawk Trail Shelburne Falls, MA 01370 USA All rights reserved.
Main Office Phone: 413.625.9776 Fax: 413.625.8498