Home Order Catalog Online Catalog New Items Contact Us
     
Search
  Current Page 233
Go to page
Click on any C CU CX part number on any page for prices
 Prev 

i
WARNING: Products on this page can expose you to a chemical, which is known to the State of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**
C392R
233
RUBBER PARTS
BOOTS – END OF TUNNEL – Where accelerator rod comes out the end of the tunnel.
1961-69 Cars C101 2 oz.
CLUTCH CABLE BOOT – '65-69: Very good repro, but does not have original metal insert.
At rear end of tunnel. C98A 6 oz.
SHIFT ROD BOOTS – Where shift rod comes out the end of the tunnel. Both are excellent repros,
but do not have the original metal insert. 1960-64 C97R 6 oz.
1965-69 C98 6 oz.
1965-69 Screws (full set) C4439 1 oz./set
GROMMETS – End of Tunnel – See page 235
TOE PANEL COVER SEALS
This dense foam seal gules to the cover (over the cables beside the accelerator
pedal). It helps prevent vibrations and keeps the cold air from coming into the car
from the lower tunnel pan area. C4870R or C6040 glue suggested – page 213.
1960-64 Cars C7367 4 oz.
1965-69 Cars C8405 6 oz. (2 pieces)
61 FC GROMMET for choke cable thru the floor, not exact but works fine. C7364 2 oz.
RUBBER DRAIN 1965-69
For 2 oval holes inside engine air inlet area. Apparently original for 1965. (Some still have the retainers in the holes). These let water out
and keeps road dirt, etc. from being sucked in. These will fit 1965-69. Order retainers separately.
DRAIN "BOOT" C5786 ea. 2 oz.
OVAL RETAINER C5786R ea. 2 oz.
BUMPERS – RUBBER
CLUTCH & BRAKE PEDAL BUMPERS: Stops pedal when you release.
1960-69 C3786 2 oz. ea.
DASH BUMPERS: Set of 10 small rubber pieces used in Spyder & Corsa dash to cushion
and prevent rattles from the gauges. C753 1 oz./set
DOOR BUMPERS
FRONT DOORS – CARS – Bumps against the body.
1960-64 (exc. 4-Door) 2 per door C355 1 oz. ea.
1960-64 All 4-Door 1 per door C355A 1 oz. ea.
1965-69 All 2 per door C356 1 oz. ea.
CONVERTIBLE DOOR "BUMPER" – These are found on the door and door pillar. 62-64 – page 225
65-69 – page 226
BUMPER KIT: 1960-64 – 4-DOOR –
Enough bumpers for 2 FRONT and 2 REAR doors (includes Wagons). C355K 4 oz./kit
REAR DOORS: 1960-64 – REAR DOORS (includes Wagons) – Used 1 rectangular and 1 round per door.
RECTANGULAR C355A 1 oz. ROUND C355R 1 oz.
1965-67 – 2 per door C356 1 oz.
WAGON REAR "Lift Door" BUMPER: 2 needed C356 1 oz.
FC DOOR BUMPERS – See pages 230-231
WHY HOLES IN RUBBER BUMPERS? Almost all rubber bumpers have a “hole” or “slit”. This is to aid in installation. If there is a round hole,
use a blunt end punch to push into the hole and extend the tip into the hole (do not push so hard you break off the tip). Bumpers with “slits”,
use a wide blunt object. Bumpers with “tail” – stick “tail” through hole & pull gently.
LICENSE LIGHT WIRE GROMMET – Usually very hard from engine heat. 1965-69 engine lid. C9650 2 oz.
ENGINE LID BUMPERS: Attach to the engine lid and prevents
rattles, 2 needed per car, EXACT REPRO. 1960-64 C354 1 oz.
1965-69 C392R 1 oz.
SCREWS – For 1965-69 – Set of 2 C4329 1 oz./set
1960-64 Engine Lid Bolt/Bumper Kits: Now you can replace those rusty bolts that screw into
the body & rubber bumper presses on. Sold set of 2 correct length bolts, 2 jamb nuts & 2 bumpers. C865 4 oz.
LID SPRING BUMPER: 1960-64 Cars – Slightly different from the original but will work
and looks the same when installed. C5383 1 oz.
1961-65 4 Spd. REPRO BACKUP SWITCH BOOT
Top quality repro. Has the 2 holes for the wires (for orig. switch only). C11554 2 oz.
MULTI-KITS
see Blue pg. MK-17
Convt. 1/4 Panel Drain
See page 295A
Wagon Door Drain
See page 222
C356
C355
C355A
C9650
C865
C354
iWARNING: Products on this page can expose you to a chemical, which is known to the State of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**C392R233RUBBER PARTSBOOTS - END OF TUNNEL - Where accelerator rod comes out the end of the tunnel. 1961-69 Cars C101 2 oz.CLUTCH CABLE BOOT - '65-69: Very good repro, but does not have original metal insert. At rear end of tunnel. C98A 6 oz.SHIFT ROD BOOTS - Where shift rod comes out the end of the tunnel. Both are excellent repros, but do not have the original metal insert. 1960-64 C97R 6 oz. 1965-69 C98 6 oz. 1965-69 Screws (full set) C4439 1 oz./setGROMMETS - End of Tunnel - See page 235TOE PANEL COVER SEALSThis dense foam seal gules to the cover (over the cables beside the acceleratorpedal). It helps prevent vibrations and keeps the cold air from coming into the car from the lower tunnel pan area. C4870R or C6040 glue suggested - page 213. 1960-64 Cars C7367 4 oz. 1965-69 Cars C8405 6 oz. (2 pieces) 61 FC GROMMET for choke cable thru the floor, not exact but works fine. C7364 2 oz. RUBBER DRAIN 1965-69For 2 oval holes inside engine air inlet area. Apparently original for 1965. (Some still have the retainers in the holes). These let water out and keeps road dirt, etc. from being sucked in. These will fit 1965-69. Order retainers separately. DRAIN "BOOT" C5786 ea. 2 oz. OVAL RETAINER C5786R ea. 2 oz.BUMPERS - RUBBER CLUTCH & BRAKE PEDAL BUMPERS: Stops pedal when you release. 1960-69 C3786 2 oz. ea. DASH BUMPERS: Set of 10 small rubber pieces used in Spyder & Corsa dash to cushion and prevent rattles from the gauges. C753 1 oz./set DOOR BUMPERS FRONT DOORS - CARS - Bumps against the body. 1960-64 (exc. 4-Door) 2 per door C355 1 oz. ea. 1960-64 All 4-Door 1 per door C355A 1 oz. ea. 1965-69 All 2 per door C356 1 oz. ea. CONVERTIBLE DOOR "BUMPER" - These are found on the door and door pillar. 62-64 - page 225 65-69 - page 226BUMPER KIT: 1960-64 - 4-DOOR - Enough bumpers for 2 FRONT and 2 REAR doors (includes Wagons). C355K 4 oz./kitREAR DOORS: 1960-64 - REAR DOORS (includes Wagons) - Used 1 rectangular and 1 round per door. RECTANGULAR C355A 1 oz. ROUND C355R 1 oz. 1965-67 - 2 per door C356 1 oz. WAGON REAR "Lift Door" BUMPER: 2 needed C356 1 oz.FC DOOR BUMPERS - See pages 230-231WHY HOLES IN RUBBER BUMPERS? Almost all rubber bumpers have a "hole" or "slit". This is to aid in installation. If there is a round hole, use a blunt end punch to push into the hole and extend the tip into the hole (do not push so hard you break off the tip). Bumpers with "slits", use a wide blunt object. Bumpers with "tail" - stick "tail" through hole & pull gently.LICENSE LIGHT WIRE GROMMET - Usually very hard from engine heat. 1965-69 engine lid. C9650 2 oz. ENGINE LID BUMPERS: Attach to the engine lid and prevents rattles, 2 needed per car, EXACT REPRO. 1960-64 C354 1 oz. 1965-69 C392R 1 oz. SCREWS - For 1965-69 - Set of 2 C4329 1 oz./set1960-64 Engine Lid Bolt/Bumper Kits: Now you can replace those rusty bolts that screw into the body & rubber bumper presses on. Sold set of 2 correct length bolts, 2 jamb nuts & 2 bumpers. C865 4 oz.LID SPRING BUMPER: 1960-64 Cars - Slightly different from the original but will work and looks the same when installed. C5383 1 oz.1961-65 4 Spd. REPRO BACKUP SWITCH BOOTTop quality repro. Has the 2 holes for the wires (for orig. switch only). C11554 2 oz.MULTI-KITSsee Blue pg. MK-17Convt. 1/4 Panel DrainSee page 295AWagon Door DrainSee page 222C356C355C355AC9650C865C354

  Current Page 233
Go to page


 Next 

Copyright © 1978, 2018 Clark's Corvair Parts, Inc., "Clark's Corvair Parts" and the "Corvair Map" are registered service marks of Clark's Corvair Parts, Inc.
P.O.Box #NET 400 Mohawk Trail Shelburne Falls, MA 01370 USA All rights reserved.
Main Office Phone: 413.625.9776 Fax: 413.625.8498