Home Order Catalog Online Catalog New Items Contact Us
 Prev 
i
WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**
334
ENGINE TOOLS
VALVE ADJUSTING EXHAUST TUBE
Adjust valves with engine running and muffler mufflering so you can hear what you are doing!
1. Remove muffler. 2. Set on ground.
3. Hook up with flexible steel tubing (pipe) to muffler (we supply enough
so car can be jacked up too!)
140's you can just unhook your hanger, loosen manifold nuts, swivel your dual muffler
out of the way.
1960-69 All (exc. Turbo & 140) C3491 2 lbs.
1962-66 Turbo C3492 3 lbs.
SPECIAL WRENCHES
CORVAIR ONLY
Make those hard jobs easy! These top quality wrenches are custom bent for those difficult nuts and bolts.
Note: C3773 is NOT too helpful for A/C & Smog idler pulley.
SPECIAL TURBO WRENCH – Allows access to the 2 bottom nuts for removing Turbo carb. "easily" C8285 8 oz.
TRANS. MOUNT WRENCH – We've discovered that our "bellhousing wrench" also works great for holding the top transmission mount bolt
on all years. About the only way to hold them! C3772 6 oz.
Fin Cleaner: Insert this grit impregnated wire into a drill and quickly remove
all flashing between fins of your head. Best way I've seen yet.
C6022A 4 oz.
Test Tube Brush: Great for cleaning inside push rod tubes, 10" long. C3957A 2 oz.
STEERING BOX ADJUSTING WRENCH
Allows screwdriver to insert into adjuster while tightening the lock nut with this wrench.
C10960 10 oz.
1960 GAS HEATER SPARK PLUG TOOL – For setting gap and position as shown in Shop Manual.
C8106 10 oz.
Special Socket oil pressure SWITCH
Yes, it's special and it works! Use with 3/8" ratchet. All Corvairs must usually remove generator or alternator.
Worth it! C5274 8 oz.
FAN BEARING GREASING TOOL
Fits Early & Late Models. Remove pulley and grease bearing in the car.
Comes with instructions. Forces grease past top seal and into bearing.
C5728 2 lbs.
REPLACEMENT "O"-RING C5728R 1 oz.
IDLER BEARING GREASING TOOL
All 1960-69 Includes instructions. C5729 8 oz.
REPLACEMENT "O"–RING C5729R 1 oz.
UNI-SYN CARBURETOR BALANCER
A MUST for exactly balancing your carburetors so your car runs smoother and cheaper.
ONLY 1 NEEDED. C1443 1 lb.
BELL HOUSING BOLTS – Those 2 you can never get to!
C3772 6 oz.
BOTTOM CARBURETOR NUT & FAN BELT IDLE PULLEY
C3773 6 oz.
NTF
You can order this part number. If not in stock, we will refund you and/or notify
you via a postcard when the part is in stock. May be 1-2 months or a year.
iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**334ENGINE TOOLSVALVE ADJUSTING EXHAUST TUBEAdjust valves with engine running and muffler mufflering so you can hear what you are doing! 1. Remove muffler. 2. Set on ground. 3. Hook up with flexible steel tubing (pipe) to muffler (we supply enough so car can be jacked up too!)140's you can just unhook your hanger, loosen manifold nuts, swivel your dual muffler out of the way. 1960-69 All (exc. Turbo & 140) C3491 2 lbs. 1962-66 Turbo C3492 3 lbs.SPECIAL WRENCHESCORVAIR ONLYMake those hard jobs easy! These top quality wrenches are custom bent for those difficult nuts and bolts. Note: C3773 is NOT too helpful for A/C & Smog idler pulley.SPECIAL TURBO WRENCH - Allows access to the 2 bottom nuts for removing Turbo carb. "easily" C8285 8 oz.TRANS. MOUNT WRENCH - We've discovered that our "bellhousing wrench" also works great for holding the top transmission mount bolt on all years. About the only way to hold them! C3772 6 oz.Fin Cleaner: Insert this grit impregnated wire into a drill and quickly remove all flashing between fins of your head. Best way I've seen yet. C6022A 4 oz. Test Tube Brush: Great for cleaning inside push rod tubes, 10" long. C3957A 2 oz.STEERING BOX ADJUSTING WRENCHAllows screwdriver to insert into adjuster while tightening the lock nut with this wrench. C10960 10 oz.1960 GAS HEATER SPARK PLUG TOOL - For setting gap and position as shown in Shop Manual. C8106 10 oz.Special Socket oil pressure SWITCHYes, it's special and it works! Use with 3/8" ratchet. All Corvairs must usually remove generator or alternator. Worth it! C5274 8 oz.FAN BEARING GREASING TOOLFits Early & Late Models. Remove pulley and grease bearing in the car. Comes with instructions. Forces grease past top seal and into bearing. C5728 2 lbs. REPLACEMENT "O"-RING C5728R 1 oz.IDLER BEARING GREASING TOOL All 1960-69 Includes instructions. C5729 8 oz. REPLACEMENT "O"-RING C5729R 1 oz. UNI-SYN CARBURETOR BALANCERA MUST for exactly balancing your carburetors so your car runs smoother and cheaper.ONLY 1 NEEDED. C1443 1 lb.BELL HOUSING BOLTS - Those 2 you can never get to! C3772 6 oz.BOTTOM CARBURETOR NUT & FAN BELT IDLE PULLEY C3773 6 oz.NTFYou can order this part number. If not in stock, we will refund you and/or notify you via a postcard when the part is in stock. May be 1-2 months or a year.
Next
CLARKS- MORE THAN PARTS.

Copyright © 1978, 2019 Clark's Corvair Parts, Inc., "Clark's Corvair Parts" and the "Corvair Map" are registered service marks of Clark's Corvair Parts, Inc.
P.O.Box #NET 400 Mohawk Trail Shelburne Falls, MA 01370 USA All rights reserved.
Main Office Phone: 413.625.9776 Fax: 413.625.8498