Home Order Catalog Online Catalog New Items Contact Us

i
WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**
41
Turbo Exhaust
PICTURE #
11. Inlet Pipes: From crossover to Turbo base. These are a very good reproduction.
Note that installing a crossover and inlet on a Turbo is a little tricky. Be sure to have
manifolds loose at the head. Everything must be lined up and in place,
then tighten every thing.
1962-64 Style C246R 4 lbs.
1965-66 Style C247R 4 lbs.
12. "Collars" (non-asbestos)
Non-asbestos (heat resistant material) packing fits around pipes where they go
thru shrouds to keep out dust, exhaust and water. Usually need to be replaced each
time removed.
1962–66 Inlet Pipe Collar C250 4 oz.
1962–66 Outlet Pipe Collar C250A 4 oz.
13. Collar Retainers: Inlet and outlet pipes go thru these (slightly different from the original but even the judges will be hard put to tell).
Sold as matched set – upper & lower. Difficult to install.
1962–64 C4374 1 lb.
1965–66 C4375 1 lb.
Retainer Bolts: Hold above retainers into the shrouding – Sold as a full set.
1962-66 Bolt Set C5630 2 oz./set
14. Gasket: Square gasket between inlet and Turbo base.
1962-66 Turbo C245 2 oz.
15. Self Locking Nuts: Hold Turbo to inlet pipe bracket. Sold Set of 4. 1962-66 Turbo C3756 2 oz./set
16. Studs – Bolts: For the Turbo exhaust housing. Holds outlet pipe on.
Note: 1962-63 The exhaust housing outlet on these is a flat, triangular surface and uses bolts (not studs).
1964-66 The exhaust housing outlet is triangular but has a recess for a round "donut gasket" – these use studs.
BOLTS: 1962-63 (Set of 3) C3161 4 oz./set
STUDS: 1964-66 (Set of 3) – Stainless Studs & brass nuts C999 4 oz./set
17.
Outlet Gaskets: See Note with #16 & picture #19. Turbo exhaust housing to outlet pipe.
Flat Triangular Gasket: 1962-63 Style C248 2 oz.
Round "Donut" Gasket: (GRAPHITE) 1964-66 Style C249 4 oz.
18. Outlet Collar: Steel triangular collar holds outlet pipe to Turbo exhaust housing – 1964-66 style.
Original Style Repro. 1964-66 Outlet Collar C1054 1 lb.
19. Outlet Pipes: From TURBO to MUFFLER. See Note #16.
1962-63 C426 6 lbs.
1964 C251 6 lbs.
1965-66 C252 6 lbs.
21. Clamps: Turbo Muffler & Tail Pipe.
Fits 1962-66 Turbo.
2 1/2" Regular Clamp C13A 6 oz.
2 1/2" Heavy Duty Clamp C13AH 8 oz.
MULTI-KITS
see Blue pg. MK-3
Turbo Base Support
See USED page 353
UNIVERSAL JOINTS
See page 167
64-66
62-63
All Aluminized
C1054
iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**41Turbo ExhaustPICTURE #11. Inlet Pipes: From crossover to Turbo base. These are a very good reproduction. Note that installing a crossover and inlet on a Turbo is a little tricky. Be sure to have manifolds loose at the head. Everything must be lined up and in place, then tighten every thing. 1962-64 Style C246R 4 lbs. 1965-66 Style C247R 4 lbs.12. "Collars" (non-asbestos) Non-asbestos (heat resistant material) packing fits around pipes where they go thru shrouds to keep out dust, exhaust and water. Usually need to be replaced each time removed. 1962-66 Inlet Pipe Collar C250 4 oz. 1962-66 Outlet Pipe Collar C250A 4 oz.13. Collar Retainers: Inlet and outlet pipes go thru these (slightly different from the original but even the judges will be hard put to tell). Sold as matched set - upper & lower. Difficult to install. 1962-64 C4374 1 lb. 1965-66 C4375 1 lb. Retainer Bolts: Hold above retainers into the shrouding - Sold as a full set. 1962-66 Bolt Set C5630 2 oz./set14. Gasket: Square gasket between inlet and Turbo base. 1962-66 Turbo C245 2 oz. 15. Self Locking Nuts: Hold Turbo to inlet pipe bracket. Sold Set of 4. 1962-66 Turbo C3756 2 oz./set16. Studs - Bolts: For the Turbo exhaust housing. Holds outlet pipe on. Note: 1962-63 The exhaust housing outlet on these is a flat, triangular surface and uses bolts (not studs). 1964-66 The exhaust housing outlet is triangular but has a recess for a round "donut gasket" - these use studs. BOLTS: 1962-63 (Set of 3) C3161 4 oz./set STUDS: 1964-66 (Set of 3) - Stainless Studs & brass nuts C999 4 oz./set 17. Outlet Gaskets: See Note with #16 & picture #19. Turbo exhaust housing to outlet pipe. Flat Triangular Gasket: 1962-63 Style C248 2 oz. Round "Donut" Gasket: (GRAPHITE) 1964-66 Style C249 4 oz.18. Outlet Collar: Steel triangular collar holds outlet pipe to Turbo exhaust housing - 1964-66 style. Original Style Repro. 1964-66 Outlet Collar C1054 1 lb.19. Outlet Pipes: From TURBO to MUFFLER. See Note #16. 1962-63 C426 6 lbs. 1964 C251 6 lbs. 1965-66 C252 6 lbs.21. Clamps: Turbo Muffler & Tail Pipe. Fits 1962-66 Turbo. 2 1/2" Regular Clamp C13A 6 oz. 2 1/2" Heavy Duty Clamp C13AH 8 oz.MULTI-KITSsee Blue pg. MK-3Turbo Base SupportSee USED page 353UNIVERSAL JOINTSSee page 16764-6662-63All AluminizedC1054
Search In Corvair Catalog Content
CLARKS- MORE THAN PARTS.

Copyright © 1978, 2022 Clark's Corvair Parts, Inc., "Clark's Corvair Parts" and the "Corvair Map" are registered service marks of Clark's Corvair Parts, Inc.
400 Mohawk Trail Shelburne Falls, MA 01370 USA All rights reserved.
Main Office Phone: 413.625.9776 Fax: 413.625.8498