Home Order Catalog Online Catalog New Items Contact Us
 Prev 
6
i
WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**
“C” VALVE STEM SEALS – VITON OR TEFLON
Valve stem seals go only on the intake valves. The solid Viton ones replace the original seals. Teflon seals last longer and
are just as easy to replace. Machine Shop doing your head? Take these seals with you and remind them to install them.
Many places are glad to have you bring the parts as they know the usual hassles to get them.
(DO NOT INSTALL ON EXHAUST VALVES.)
Viton Valve Stem Seals Set of 6: C1030 2 oz. Set of 3: C1030X 1 oz.
Teflon Valve Stem Seals Set of 6: C5857A 2 oz. Set of 3: C5857 1 oz.
“D” OPTIONAL FOAM
ENGINE SHROUD FOAM SEAL KIT – BLACK – ADHESIVE BACKED
Help keep water out and heat into your heating system.
Note: These seals are included in our “EVERYTHING” Gasket
Sets and some "Multi" Kits. Check that you don’t end up with an
extra set. The Kits include a Turbo seal and seal originally used
only on 61-64 but we have discounted the set enough so these
are free. Also available separately below.
61-69 ALL C203A 12 oz.
INDIVIDUAL FOAM SEALS
“E” INDIVIDUAL GASKETS & SEALS
PERMATEX #2: See page 13 for more info. 3 oz. tube C715 2 oz.
GASKET REMOVER SPRAY: Quickly removes baked on gaskets, adhesives, glues and carbon. When using
on aluminum, rinse off after use. Helps prevent scratching of gasket surface. C5779 12 oz. CAN’T SHIP BY AIR
VALVE COVER GASKETS: 1960-69 ALL GM VALVE COVERS
OIL PAN GASKETS: 1960-69 ALL
PICTURE #1: FOAM SEAL – Fits between lower
shroud and head. Helps keep any oil that leaks
from valve cover from getting into shrouds, and
helps keep out dust and water.
1960-69 – either side – (2) required
C203 1 oz.
PICTURE #2: FOAM SEAL – Fits inner edge of
lower shroud and block (near oil pan). Keeps oil
leaks from pan from entering shroud.
1960-69 – (1) is enough for both sides
C204 1 oz.
PICTURE #3: FOAM SEAL – On sides of lower
“skid” plate – as shown.
1960-69 – (1) is enough for both sides
C4627 2 oz.
FOAM SEAL – Goes at the bottom of the shroud
at lower back of engine. The one that you see
when you first remove rear alr outlet grill.
1961-69 ALL
C1075 1 oz.
FOAM SEAL – Original for 1961-64. Can be used
on 1965-69. Fits between front shroud (where gas
line comes thru) and top of engine block.
1961-64
C1076 1 oz.
FOAM SEAL – Fits all cars and vans 1961-69.
Where heater hose adaptor ducts bolt to shroud.
Prevents heat loss.
1961-1969
Left Side All
Right Side All (exc. Turbo)
C2285 2 oz.
Right Side – Turbo C2286A 2 oz.
4 Hole Valve Cover Gaskets
Rubber C201 ea 4 oz.
Rubber & Cork C3018 ea 4 oz.
Blue Silicone C10912 ea 4 oz.
6 Hole Valve Cover Gaskets
Rubber C201-6 ea 4 oz.
Rubber & Cork C6119 ea 4 oz.
Blue Silicone C10912-6 ea 4 oz.
Aluminum Valve Cover Gaskets
Clark & OTTO valve
covers (4 or 6 hole)
C3941 (set of 2) 4 oz.
“Econo” & No Name Aluminum valve covers use any
cork or rubber gasket listed above. (4 or 6 hole as
needed) Trim side tabs as needed.
1
2
3
NOTE: “Paper” type suggested only for new GM pans or aluminum pans.
Super Cork & Rubber C199 6 oz.
“RUBBERY” composition C3129 6 oz.
SILICONE OIL PAN GASKET C10914 6 oz.
Cork & Rubber (thinner – for aluminum pans) C199T 6 oz.
“PAPER” – GM style C200 6 oz.
“PAPER” – Aluminum pans C3937 6 oz.
SILICONE GASKETS ABOVE: Exact Replacement, HIGHER temperature range,
MORE oil resistant, and can be REUSED several times. Sold EACH.
NOT in ANY of our KITS.
OIL DRAIN PLUG GASKETS: 1960-69 ALL pans including aluminum (not for
oversize plugs). We offer the original style nylon and copper (less apt to crack or
allow plug to loosen). NYLON – C439 1 oz. COPPER – C6057 1 oz.
COPPER (for oversize plugs) – C6060 1 oz.
C2285
STOCK OIL PAN REINFORCEMENT "RAIL"
This steel piece is about 3/16" thick and completely reinforces the
bolting of your stock steel oil pan and should eliminate leaks. Comes
with correct length bolts, order gasket separately.
C13374 4 lbs.
C203A
6iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**"C" VALVE STEM SEALS - VITON OR TEFLONValve stem seals go only on the intake valves. The solid Viton ones replace the original seals. Teflon seals last longer and are just as easy to replace. Machine Shop doing your head? Take these seals with you and remind them to install them. Many places are glad to have you bring the parts as they know the usual hassles to get them. (DO NOT INSTALL ON EXHAUST VALVES.) Viton Valve Stem Seals Set of 6: C1030 2 oz. Set of 3: C1030X 1 oz.Teflon Valve Stem Seals Set of 6: C5857A 2 oz. Set of 3: C5857 1 oz."D" OPTIONAL FOAMENGINE SHROUD FOAM SEAL KIT - BLACK - ADHESIVE BACKEDHelp keep water out and heat into your heating system. Note: These seals are included in our "EVERYTHING" Gasket Sets and some "Multi" Kits. Check that you don't end up with an extra set. The Kits include a Turbo seal and seal originally used only on 61-64 but we have discounted the set enough so these are free. Also available separately below. 61-69 ALL C203A 12 oz.INDIVIDUAL FOAM SEALS"E" INDIVIDUAL GASKETS & SEALSPERMATEX #2: See page 13 for more info. 3 oz. tube C715 2 oz.GASKET REMOVER SPRAY: Quickly removes baked on gaskets, adhesives, glues and carbon. When using on aluminum, rinse off after use. Helps prevent scratching of gasket surface. C5779 12 oz. CAN'T SHIP BY AIR VALVE COVER GASKETS: 1960-69 ALL GM VALVE COVERS OIL PAN GASKETS: 1960-69 ALLPICTURE #1: FOAM SEAL - Fits between lower shroud and head. Helps keep any oil that leaks from valve cover from getting into shrouds, and helps keep out dust and water. 1960-69 - either side - (2) requiredC203 1 oz.PICTURE #2: FOAM SEAL - Fits inner edge of lower shroud and block (near oil pan). Keeps oil leaks from pan from entering shroud. 1960-69 - (1) is enough for both sidesC204 1 oz.PICTURE #3: FOAM SEAL - On sides of lower "skid" plate - as shown. 1960-69 - (1) is enough for both sidesC4627 2 oz.FOAM SEAL - Goes at the bottom of the shroud at lower back of engine. The one that you see when you first remove rear alr outlet grill.1961-69 ALLC1075 1 oz.FOAM SEAL - Original for 1961-64. Can be used on 1965-69. Fits between front shroud (where gas line comes thru) and top of engine block.1961-64C1076 1 oz.FOAM SEAL - Fits all cars and vans 1961-69. Where heater hose adaptor ducts bolt to shroud. Prevents heat loss. 1961-1969Left Side All Right Side All (exc. Turbo) C2285 2 oz.Right Side - Turbo C2286A 2 oz.4 Hole Valve Cover GasketsRubber C201 ea 4 oz.Rubber & Cork C3018 ea 4 oz.Blue Silicone C10912 ea 4 oz. 6 Hole Valve Cover GasketsRubber C201-6 ea 4 oz.Rubber & Cork C6119 ea 4 oz.Blue Silicone C10912-6 ea 4 oz.Aluminum Valve Cover GasketsClark & OTTO valve covers (4 or 6 hole)C3941 (set of 2) 4 oz."Econo" & No Name Aluminum valve covers use any cork or rubber gasket listed above. (4 or 6 hole as needed) Trim side tabs as needed. 123NOTE: "Paper" type suggested only for new GM pans or aluminum pans.Super Cork & Rubber C199 6 oz."RUBBERY" composition C3129 6 oz.SILICONE OIL PAN GASKET C10914 6 oz.Cork & Rubber (thinner - for aluminum pans) C199T 6 oz."PAPER" - GM style C200 6 oz."PAPER" - Aluminum pans C3937 6 oz.SILICONE GASKETS ABOVE: Exact Replacement, HIGHER temperature range, MORE oil resistant, and can be REUSED several times. Sold EACH. NOT in ANY of our KITS.OIL DRAIN PLUG GASKETS: 1960-69 ALL pans including aluminum (not for oversize plugs). We offer the original style nylon and copper (less apt to crack or allow plug to loosen). NYLON - C439 1 oz. COPPER - C6057 1 oz.COPPER (for oversize plugs) - C6060 1 oz.C2285STOCK OIL PAN REINFORCEMENT "RAIL"This steel piece is about 3/16" thick and completely reinforces the bolting of your stock steel oil pan and should eliminate leaks. Comes with correct length bolts, order gasket separately. C13374 4 lbs.C203A
Next
CLARKS- MORE THAN PARTS.

Copyright © 1978, 2019 Clark's Corvair Parts, Inc., "Clark's Corvair Parts" and the "Corvair Map" are registered service marks of Clark's Corvair Parts, Inc.
P.O.Box #NET 400 Mohawk Trail Shelburne Falls, MA 01370 USA All rights reserved.
Main Office Phone: 413.625.9776 Fax: 413.625.8498